I realize there is still some confusion regarding Cisco Nexus FEX as it relates to ToR connected FEX, which is a Cisco Nexus 2K FEX with a Cisco Nexus 5K/7K/9K as a parent switch, and the FEX you find in UCS, which we can refer to as “Blade-FEX”. I am going to outline what ToR (Top of Rack) FEX in this blog post, not Blade-FEX, to help bring some clarity around this still confusing terminology. This is also not meant to bring any additional ambiguity, but it is true you can use certain Cisco Nexus 22XX ToR-FEX and “parent” them to a Cisco UCS Fabric Interconnect; however, I would not classify this as Blade-FEX or ToR-FEX, I’d like to coin it with the term “Fabric-FEX”, you owe me $1.00 every time you use this, send it via paypal :). Thus, moving forward, we’re going to refer to a FEX which parents to a Cisco Nexus switch as a ToR-FEX.

Cisco Nexus FEX works thanks to the Cisco pioneered 802.1BR, click here for more information. Now, you don’t have to worry about configuring the gory details of what is essentially VN-TAG because this is all handled with a few simple commands to get your FEX up and running; however, this is just here do you know how FEX works to communicate with the parent switch underneath the sheets.

The logical representation of FEX is broken down like this:

  • Logical Interfaces (LIF) – This is simple, its the Eth1xx/1/X representation on the switch
  • Network Interfaces (NIF) – These are the physical uplinks connecting the FEX to parent, carrying the VN-TAG
  • Virtual Interface (VIF) – This is the logical interface which correlates, in software, to the physical host interface. We we wil discuss this in a minute about why this makes FEX capable of full swap of a failed FEX without reconfiguring the host ports
  • Host Interface (HIF) – These are the physical ports on the FEX which you connect your hosts to. The parent switch assigned each HIF a unique VN-TAG ID, which is roughly correlated to the above Virtual Interface (VIF) assignment.

Here is some output to take a peek at, taken from a Cisco Nexus 9332PQ switch with 2348TQ and 2348UPQ FEX attached:

slot:36, fab_if:160001f4, p_ind:f4010016, p_numelem:1
dev_inst:0, nif_no:16, hif_no:40, nif_ind:160001f4, hif_ind:1f670a00
Eth104/1/42 0x1f670a40 Down Po501 Po501 NoConf

Take notice, this is Logical port: Eth104/1/42 and there is a plethora of information regarding the port, including the HIF numer and the hif_ind. I haven’t referenced anything with Cisco as of yet, but I would believe the HIF no is the unique number assigned to the port, perhaps the VIF, and the HIF_IND may be an index ID, but I’ll investigate later. For now, just take notice that: Eth[101-199]/1/[1-48] is the LIF, which is attached to a VIF, which correlates to the HIF on the FEX. Because FEX attaches the configuration to a VIF, which is also correlated to the FEX ID, you can have your FEX member, say FEX 104, fail completely and all you need to do is just replace the failed FEX, cable it the same way and when the FEX image is downloaded it’ll reboot and continue operation without the need to rebuild the configurations.

Now, you MUST be diligent in understanding the valid UPLINK topology you can configure your ToR-FEX for, in relation to your parent switch. Always review the configuration guide for your specific model of FEX and parent switch to obtain the valid topology. In my scenarios with the Cisco Nexus 9K switches I do a single-homed, host vPC port-channel uplink topology because we can’t do a more elaborate e-vPC design with the 9K switches and our hosts will be attached with port-channels in an active-active scenario.

Finally, the configuration is simple; however, some Cisco documentation is confusing because the wording in some documents states the UPLINK port-channel is LACP enabled; thus, you would assume you configure your UPLINK as an active LACP member. This is wrong, in fact, the best method, at least from my experience with the 9K switches, is to create the port-channel you’ll be using for the UPLINK, no-shut the interface and nothing more, then move into the physical interfaces that’ll be part of this port-channel, no shut the interfaces and just assign them to the port-channel as static mode. Then, move back into the port-channel configuration mode and build your configuration. Below is the basic configuration you need to get your FEX attached to your 9K switch:


interface po500
no shut
!
interface eth1/21-24
channel-group 500
no shut
!
int po500
switchport
switchport mode fex-fabric
fex associate
mtu
no shut -
!

A note about setting Jumbo frames on those FEX ports. The FEX host ports will assume the maximum MTU based on the UPLINK port-channels MTU assignment. In our environments we aim to have jumbo frames end-to-end and leave it up to the specific host/OS/application to decide on its optimal packet size. Thus, if you set your MTU on the UPLINK port-channel to 2000, your MTU on will be 2000 on your host interface ports on the FEX.

As an update, and to summarize, here are the FEX types to help clear up confusion, these are not “official” terms, but these will help to clear up confusion, I hope:

  • ToR-FEX: A Nexus 2K FEX attached (Parented) to a Nexus 3K/5K/7K/9K switch for extending ports
  • Blade FEX: These modules are installed into a Cisco UCS chassis
  • Fabric-Interconect FEX: These are the same Nexus 2K FEX used for parenting to 3K/5K/7K/9K; however, now you can attach (Parent) these Nexus 2K FEX to Cisco Fabric Interconnects for the purpose of extending ports for your Fabric Interconnects, or providing a different type/speed of port.

Comments are closed.